harman P43 Install

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

padfitz

New Member
Oct 16, 2011
26
NEPA
New pellet user, new to forum and excited to be here. This year we installed a Harman P43 ourselves. To start, the house is a raised ranch, 2000 sqft with electric baseboard and ventless propane in lower section. Decided on a location and built the chimney to include cutting an 8 inch hole in the poured concrete foundation. That was loads of fun by the way. Next was the re-building of the wall to support the Cultured Stone. This was done with 2x4 studs, 3/4 plywood, topped with 15 lb felt paper to waterproof, then metal lathe for the scratch coat. I must say that I have a new found appreciation for the mason trade. I then built the raised hearth out of 2 course of brick topped with Cultured Stone Hearth stones. The stove is vented with BDM pellet pipe, 3" increased to 4" pipe thru the wall, then to a 4" S/S insulated liner. I built the chimney and installed a tile liner but thought an insulated 4" liner would hold the heat better and provide a better draft. Next to this is an outside air intake so the system is 100% closed to the inside. No need to pull air from in the house to run this. I then ran a dedicated electrical line, 20A, to the stove to make sure we do not have any issues.

I tried to think of everything and would like to hear some feedback.

To date, have only ran 5-6 bags of Allegheny pellets through it with no complaints. Run the stove in "stove temp" mode on low with a #3 feed rate and in the middle for temp. It has not been to cold outside but, it gets quite hot downstairs and the upstairs is 72-74 degrees. Nice change to the "wet" feel of the propane and the $$$$$ of the electric coming on.

Paid $229 a ton and have 3 stored.

Thanks for looking and I look forward to some feedback,

Dan
 

Attachments

  • 1.jpg
    1.jpg
    40.9 KB · Views: 428
  • 1.jpg
    1.jpg
    46.1 KB · Views: 514
  • 1.jpg
    1.jpg
    49.6 KB · Views: 441
  • 1.jpg
    1.jpg
    42.4 KB · Views: 685
  • 1.jpg
    1.jpg
    42.5 KB · Views: 442
Very nice install and well thought out. I see the pup already found the hot spot without the stove even being on! Enjoy
 
Welcome padfitz,

Glad you joined and shared your install. You sure did a lot of work and homework. Outstanding job!

P.S.
I think the dog wants you to turn the stove on! :)
 
Welcome! I agree with the other posts, very well thought out and very nice install!
 
Looks great... Lots of work you pit into it. But it will soon pay you back.

Welcome to the Forums. Beautiful dog you have. I am sure you will be fighting over the best spot.

X2 on the surge protector. You spent a lot of money on your investment. Spend a couple extra bucks and get a good one. Over 1,000 joules is good. But close to 2,000 is great. Tripplite makes some good ones.

Looking at the picture and having a "black" outlet. You may have one. We like to double check. A black pr brown out can wipe a control board out quick.
 
Did not even think about a surge protector or battery back up for that matter. Will be researching them over the next few days.

Thanks


Pup is a yellow lab, nicest dog we have had, and just loves to be around people. No bad manors, we just have to find out how to contain the hair........ lol
 
I do not think I am more talented, just have the ability to see it in my mind and get it done. That and the fact that I cannot part with anymore money than I have to is a BIG motivator......
 
Status
Not open for further replies.