pellet furnace ?

Post in 'The Pellet Mill - Pellet and Multifuel Stoves' started by mchud, Jul 21, 2008.

Thread Status:
Not open for further replies.
  1. mchud

    mchud
    Expand Collapse
    Member

    Joined:
    Jul 21, 2008
    Messages:
    5
    Likes Received:
    0
    Loc:
    western mass
    I decided to start looking at a pellet furnace but now have found they are hard to come by. I wanted to go with a harmon but as we know thats out. The one furnace i have found that i can actualy get in august is a us stove model 6100 is this a good choice? It is coming form a reputable place. But not sure on the quality. This furnace will be used to supplement my oil heat in a 2000 sf house. Thanks for the help
     

    Helpful Sponsor Ads!





  2. webbie

    webbie
    Expand Collapse
    Seasoned Moderator
    Staff Member

    Joined:
    Nov 17, 2005
    Messages:
    12,190
    Likes Received:
    1,086
    Loc:
    Western Mass.
    Are there any Magnum furnaces available?
    http://www.americanenergysystems.com/magnum7500.cfm

    Relatively reasonable, reliable and made my a very small company....they also help sponsor this site!

    Nothing against US Stove, but it might be tougher to get information and service on them since they tend to sell through tractor supply and such places - where info and service cannot be had.
     
    Collapse Signature Expand Signature
  3. mchud

    mchud
    Expand Collapse
    Member

    Joined:
    Jul 21, 2008
    Messages:
    5
    Likes Received:
    0
    Loc:
    western mass
    Thanks for the info i cobntacted a dealer this morning and they were full of info. It looks like i am probaly going to go with the magnum. Unless any one has any other suggestions. Thanks again
     
  4. hossthehermit

    hossthehermit
    Expand Collapse
    Minister of Fire

    Joined:
    May 17, 2008
    Messages:
    2,568
    Likes Received:
    533
    Loc:
    Maine, ayuh, by gorry
    Have you looked at St' Croix?
     
    Collapse Signature Expand Signature
  5. drewmo

    drewmo
    Expand Collapse
    Feeling the Heat

    Joined:
    Nov 20, 2006
    Messages:
    313
    Likes Received:
    62
    Loc:
    Central Maine
    Not sure of availability in the US, but a neighbor has an HS Tarm MB-Solo and is quite pleased with it.
     
    Collapse Signature Expand Signature
  6. mchud

    mchud
    Expand Collapse
    Member

    Joined:
    Jul 21, 2008
    Messages:
    5
    Likes Received:
    0
    Loc:
    western mass
    Thanks i will check them out. Too many choices, Probaly should of thought of this earlier in the year. Thanks for the help
     
  7. sinnian

    sinnian
    Expand Collapse
    Minister of Fire

    Joined:
    May 28, 2008
    Messages:
    894
    Likes Received:
    54
    Loc:
    Limerick, Maine
    Collapse Signature Expand Signature
  8. mchud

    mchud
    Expand Collapse
    Member

    Joined:
    Jul 21, 2008
    Messages:
    5
    Likes Received:
    0
    Loc:
    western mass
    I just ordered a Magnum 6500 furnace. thanks for all the advice. They seem to be a good unit and realy couldnt find much for choices that i could actualy get for this winter. Thanks again and look forward to putting it in. Hopefuly have it instaled in a few weeks. Take care
     
  9. Iluvwinter

    Iluvwinter
    Expand Collapse
    Member

    Joined:
    Jul 28, 2008
    Messages:
    28
    Likes Received:
    0
    Loc:
    Smyrna,Ny Upstate
  10. kinsmanstoves

    kinsmanstoves
    Expand Collapse
    Minister of Fire

    Joined:
    Aug 29, 2007
    Messages:
    3,471
    Likes Received:
    499
    Loc:
    Ravenna, Ohio 44266
    Collapse Signature Expand Signature
Thread Status:
Not open for further replies.

Share This Page

Entire Site copyright © 1995-2016 - email to webinfo@hearth.com
Hearth.com and HearthNet are property and trademarks of Hearth.com LLC Advertising Information