Quadrafire owners......

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
jtp10181 said:
It is very easy to access, take a few screws off the back of the left side panel and lift it up and out. You will be able to see how it works exactly. If I remember correctly the front flap is the start-up and the read flap is the burn rate. I have seen a couple units where the slider rod dislodged binding up the whole system.

Since I last posted, my timer doesn't seem to be working at all now - I don't hear any tick-tick-tick. It's supposed to be mild here for the next few days, so I think I'll try to take a look back there and poke around a bit.
 
Redox

Three years ago I got a 3100 quad and I did the white out thing to,that just to funny that people from the east coast would copy the people(ME) from the west coast lol. It was in year two that i would open up the drafts and let the bed of coals burn down for about one hour before i load it for the nite burn. I just think that its funny the way GREAT mines work lol.
 
I wouldn't call it a great mind here on the east coast. :roll: I just was looking for a quick solution to getting the stove back to a steady burn. Something about necessity being the mother of invention. Maybe we can patent it and sell it back to Quad!

Any luck, Seth? If anything is broken, it should be covered by the warranty.

Quadrasnob: One who believes that their stove is the greatest thing since canned beer and can't figure out how anyone could buy anything else. :coolsmile:

see also:

Summithead
Hearthstoner
Blaze King Elitist
Englandnut

Have I missed anyone?

Chris
 
I haven't dug in yet - I'm working today so I'll probably take a look tomorrow.
 
So I didn't end up opening the timer section up. I was playing around with it and it seemed that when I was pushing the air control all the way back and then forward, it wasn't going quite all the way back. If I went to the back of the stove and manually pushed the back lever just a bit further, it seemed to engage the timer everytime. Now clearly this is not working as intended but if that is the extent of the issue then I'm not too concerned about it at this point.
 
Redox said:
Quadrasnob: One who believes that their stove is the greatest thing since canned beer and can't figure out how anyone could buy anything else. :coolsmile:

see also:

Summithead
Hearthstoner
Blaze King Elitist
Englandnut

Have I missed anyone?

Chris

Woodstocked

Vermont Castigator

Napoleonic

Country Bumpkin

Vogelzangist

Bucked Up
 
Where can I order a replacement label for my start-up air control for my Quadra-Fire 4300 Millennium, ACC? No one seems to know how it got skinned up. Amazing, huh?
 
Did you try your Quad dealer? That's the only place you will be able to get one, if at all.
 
jtp10181 said:
offroadaudio said:
Well, it's an insert so remove surround, lift heavy stove, slide, try not to scratch tile hearth extension........
I'll just keep going like I am now - I just crack the door a little at start up - works well for me and wood consumption is not excessive.
I only go through 2 chords a season.

Sorry, you do not have a timer system at all. My previous comment was geared at GunSeth.

offroadaudio, you should have two "shotgun" holes in the back. This is where the start-up air comes in. Check with a light and make sure they are not full of ash. Also when you push the lever in you should be able to see the flap door move back. I can normally see a huge difference with the fire going well, and then shutting the start-up air. Try with a decent fire going, open the start-up air and then shut the burn rate down all the way. Then close the start-up air after the flames stabilize. You should instantly see a change in the flames.

Thanks for this info - I just checked with a flashlight (first time my stove has been cool in a month) I vac'd out the shot gun holes and saw the flaps. The flaps are about 2 - 3" into the holes and are closed - pushing and pulling the start up air lever does nothing to change them - it's broken.
I'm actually glad about this - it confirms my thought, and is probably an easy fix once the insert is out of the fireplace - not going to happen until spring.

But thank you.

'Frank
 
Hmmm I have had many people "think" the startup air was broken, but never seen one actually break. Its a pretty simple mechanism. Only thing I can think of is if one of the welds at the rear broke in half.
 
Whops, double post.
 
jtp10181 said:
Hmmm I have had many people "think" the startup air was broken, but never seen one actually break. Its a pretty simple mechanism. Only thing I can think of is if one of the welds at the rear broke in half.

Maybe we bumped it during install?
 
I have a Quadra-Fire 4300 Millenium I got in 02 and like the no frills stuff. When the electricity goes off I will always be warm.
Now if I could only figure out how to unlock my gas cook stove when the power goes out.
 
Status
Not open for further replies.