I bought a used m55 knowing that I needed to replace blower for overheats. Installed stove planning on running on low until blower comes. Installed turned on stove. Set to manual. The temperature indicator has a red light at 5 and 1. The stove fans kick on etc...no pellets drop. After 5 minutes or so the 4 starts blinking. The heat sensor didn't seemed tripped nor has it been running. This is all from cold start. Any ideas?
Enviro m55 cast start up
- Thread starter newwoodguy
- Start date
-
Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.
We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.
We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil. -
Super Cedar firestarters 30% discount Use code Hearth2024 Click here
Ssyko
Minister of Fire
Did you give it a good cleaning before trying to run it? Im assuming it is the convection blower you ordered? Does the combustion motor run when you turn on? How is your exhaust vent configured? OAK? (Outside air kit)
The combustion/exhaust fan kick on. The chimney is pretty standard out the wall with 4 feet of vertical. Oak is 4 inch no bends straight out the wall. The conviction blower is the part that I was told needed replaced. So yes that's the part ordered. The manual says that the blinking 4 is overheat sensor but it's not running.
So that is issue. I located the sensor and it isn't pushing. I think I'm going to replace.it as well. Either it isn't tripped or it is stuck in tripped position.
That is the usual problem but there may be others .Note the
button resets with just a light touch . Try connecting the wires
together and see if the auger works . If it is that sensor the stove
should fire up and work as normal . Also make sure you are in
manual mode if you are not using a thermostat.
button resets with just a light touch . Try connecting the wires
together and see if the auger works . If it is that sensor the stove
should fire up and work as normal . Also make sure you are in
manual mode if you are not using a thermostat.
Tried. No dice. The stove comes on. Exhaust coming out of chimney. Air coming in through oak just doesn't light and after 2 or 4 minutes just blinks 4. The frustrating thing is the guy I bought it from tested it and it came on.
Here is a link to the enviro teck service manual
Page 54 #4 Flashing == tripped high temp sensor
http://enviro.com/custom_content/docs/manuals/C-12145 Instruction PELLET Service Manual.pdf
Page 54 #4 Flashing == tripped high temp sensor
http://enviro.com/custom_content/docs/manuals/C-12145 Instruction PELLET Service Manual.pdf
Yeah I'll have to just contact the dealer. At this point hopper is closed and I bypassed the sensor so it shouldn't matter if it's tripped. When I start stove it doesn't even to to run auger or drop pellets. Just runs fans for 5 min then flashes 4
What type is your stove a Cast, Free Standing or an insert
Check the vac switch make sure all doors are closed and latched
There is a poss. that lack of vac. is the problem
Check the vac switch make sure all doors are closed and latched
There is a poss. that lack of vac. is the problem
A flashing #4 is the High heat sensor tripped AND also if the Hopper Fill door is open for greater than 2 minutes. Are you closing the cast fill door on top of the stove? There is a magnetic switch on the control pad that works with a small magnet on the underside of the hopper fill door.
---Nailer---
---Nailer---
Bought
Bought used. Wondered what that magnet stuck to side of.stove was. Fired up perfect. Thanks a ton.
Similar threads
