We're building a new house (almost done!) and will be heating primarily with wood. Just bought a BlazeKing Princess - got a good deal on a floor model. Now we need to purchase and install the chimney. The stove will be located near the center of the house and the chimney will run straight up through a bedroom and out the roof. It's a cape-cod style house. The roof is metal and is a 10/12 pitch. Is it possible to get a stove pipe that is removable, so we can clean from below? If it exists, what is it called? Rather not have to get up on that roof too often.
New chimney install - clean from inside?
- Thread starter ljensen1
- Start date
-
Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.
We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.
We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
- Status
not a cheap solution, but one that works well is the boz mechanical chimney cleaning system
(broken link removed)
(broken link removed)
I'm not familiar with how the BK Princess is configured inside, so this simple solution may/may not be applicable. If you can access the firebox outlet to the flue (you may have to remove some internal components), then you can do an effective job from the bottom up with a Gardus SootEater. I have this tool. I hate going up on my 7/12 pitch tile roofs. I like using this. Here's the link...sorry about the cheesy auto-start video. %-P Rick
http://www.sooteater.com/
http://www.sooteater.com/
fossil said:
http://www.sooteater.com/chimney/
i love the pic of an earthstove t150c on this page
one fun stove to clean from inside...Not familiar with that stove, either...but I have no problem with my little CFM in the shop, or my Lopi Liberty in the house. Remove baffles firebricks...which is part of cleaning anyway. Beats going up on the roof in my 61-y/o book, and the thing negotiates corrugated back-to-back single wall 45°'s with ease. Got a conventional poly brush stuck hard in the shop stove flue once, and had to disassemble the whole darned thing to get it out. What a mess that was. I'm not trying to say that this thing is the answer for everyone, but it sure does work well in my situation. Rick
ETA: Found my pics of the thing that I posted in a thread some time ago.
ETA: Found my pics of the thing that I posted in a thread some time ago.
Attachments
![[Hearth.com] New chimney install - clean from inside?](/talk/data/attachments/30/30023-24929c72bb303b788e87af100775200c.jpg?hash=-ZHqwRsIV0)
![[Hearth.com] New chimney install - clean from inside?](/talk/data/attachments/30/30024-0266bcf4d741e6dcb4bbdbb980a946b4.jpg?hash=wsUNkxO7Zp)
Thanks for the suggestions. The Princess is a catalyst stove and it looks like I can't clean from within the stove.
Has anyone used the BOZ mechanical cleaner? Also, I thought I saw mention in a past thread of some kind of telescoping or removable section of stove pipe. Anyone know anything about that?
Thanks!
Has anyone used the BOZ mechanical cleaner? Also, I thought I saw mention in a past thread of some kind of telescoping or removable section of stove pipe. Anyone know anything about that?
Thanks!
You can get telescoping connector pipe. It makes disconnecting the stove easy. I'll dig up a link.
Double-wall:
(broken link removed to http://www.northlineexpress.com/multiple_items.asp?cc=6DVL)
Single-wall:
(broken link removed to http://www.northlineexpress.com/multiple_items.asp?cc=6DuraBlack)
Double-wall:
(broken link removed to http://www.northlineexpress.com/multiple_items.asp?cc=6DVL)
Single-wall:
(broken link removed to http://www.northlineexpress.com/multiple_items.asp?cc=6DuraBlack)
Thank you. I'm going to look into that further. I take it that it's okay to unfasten and re-fasten the telescoping pipe regularly for cleaning? It can handle that?
The opening for the chimney is on the top of the stove. To offset, I'd have to add two bends. I would rather not do that.
Do you think a single wall tee would be better than a telescoping pipe? It would certainly be easier to access, but would the cleaning be easier and more thorough if I actually removed a whole section of pipe?
Thanks everyone for your patience in answering. Haven't had any experience in this area yet.
Thanks everyone for your patience in answering. Haven't had any experience in this area yet.
The bypass on the princess opens a trap door almost directly beneath the flue collar. You will probably be able to get a soot eater up through there, or a soft nylon brush. A slip joint would probably be safer though and prevent you from sending soot down into the cat area.
Congrats on the purchase!
Congrats on the purchase!
Thanks for the info. I was concerned about getting soot where it shouldn't be.
What's the difference between a slip joint and a telescoping stove pipe?
What's the difference between a slip joint and a telescoping stove pipe?
Rick,
do you have a screened cap? and does the soot eater clean it well?
edit:
to the OP,
just remember, even if you can clean from the bottom to do yearly inspection from the top
maint. isn't just cleaning, but also inspecting
do you have a screened cap? and does the soot eater clean it well?
edit:
to the OP,
just remember, even if you can clean from the bottom to do yearly inspection from the top
maint. isn't just cleaning, but also inspecting
I use the Sooteater as well and have had good results cleaning both my Oslo and Castine from the inside. The sooteater negotiates 45 degree bends and does a serviceable job of cleaning the cap as well.
joe
joe
Is there a limit on the snout length in the thimble to where cleaning from the bottom up won't work? I don't mind going to the roof, but doing it from the basement would be much nicer.
A slip joint and a telescoping pipe are the same thing.
WoodHeatStoves is correct, after you clean from the bottom please make sure you get on the roof and inspect things. I clean client chimneys from the bottom as often as possible, but it is absolutely necessary to get on the roof and inspect things afterward. It's just nice (and safer) to not have to lug tools up a ladder.
WoodHeatStoves is correct, after you clean from the bottom please make sure you get on the roof and inspect things. I clean client chimneys from the bottom as often as possible, but it is absolutely necessary to get on the roof and inspect things afterward. It's just nice (and safer) to not have to lug tools up a ladder.
Thanks for the reminder. It will be a lot easier to get up there and just "look" rather than having to clean from that perch.
- Status
