I have a post in here that I'm looking for a new light weight saw, was just reading updates on it and figured, I should toss out the reminder that we all know anyways regarding safety glasses. Last spring I was doing a "quick last cut" and didn't bother putting my glasses back on (they were sitting on the rack of my ATV). In a moment of stupidity I had a wood chip (or something) fly into my eye. I ended up at urgent care and missed a few days of work. No lasting damage but I did get a torn cornea and for anyone who isn't aware...an eye injury is an extremely painful ordeal and there are no pain meds that will touch it. They are completely avoidable and since doing this I wont touch a saw, or any power tool without safety glasses on. When I healed up I went and bought about 6 pairs of safety glasses and placed them on my wood bench, my table saw, and one stays on my chainsaw. I also bought a helmet with face shield. Anyway, if I can keep one person from going through the pain I did by throwing out this reminder then I'd feel good. Again, I'm sure everyone already is aware of this and probably already wears safety glasses but if there's just one person who doesn't wear safety glasses and reads this...please get a pair and wear them!
Wear eye protection when using chainsaws
- Thread starter MJFlores
- Start date
-
Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.
We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.
We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil. -
Super Cedar firestarters 30% discount Use code Hearth2024 Click here
- Status
Firewood Bandit
Minister of Fire
I wear a helmet/face shield/ear muff system. However even with the face shield, you need glasses on.
MJ: Thanks a trillion for sharing what could have been a life altering ordeal. Often people need a story like yours to coax them into getting religious about safety procedures. It's seems its usually "that one last cut" that causes the problem, because of being tired or just plain haste. That's not a criticism, I have personally been guilty of that and suffered the consequences.
I'm glad your story ended well - I cannot even imagine the pain of your injury.
I'm glad your story ended well - I cannot even imagine the pain of your injury.
Last edited:
I am a fan of the hard hat with face shield and ear protection. I do not wear safety glass under the face shield because my safety glass fog up due to sweating, which then becomes, imo, more dangerous. That face shield screen to me is the best and of course the hearing protection is the best. I am actually due for a new face shield mine is bent and starting to pop up when I don't want it to popup. Don't forget a good shoes, I've got a pair with steel toe protection.
Agreed on not using glasses under the shield. Mine has a screen with pretty small holes - I wonder if anyone make a plastic shield?
Glasses that fog up are just as dangerous as no glasses.
Glasses that fog up are just as dangerous as no glasses.
Helmet/face shield/ear protection here - also sturdy boots and chaps. Haven't had any issue with glasses fogging too badly with the face shield - normally wearing sunglasses. Cheers!
After my injury, I wear safety glasses under neath my face shield. Last summer I did have some fogging, but found if I moved the glasses out away from my face just a bit the problem went away. I also found that wearing glasses without the shield lessens the fogging problem quite a bit. During real humid weather I leave the shield up and rely on the glasses. My shield is mesh, so I'd rather have safety glasses and no shield than a shield of mesh and no safety glasses. I try very hard to use both though. After the pain I had to go through, having to sit with both eyes closed for almost three days, and wondering if I had permanent vision loss was enough to make me a huge safety glasses advocate. Next on my list is some saw chaps...and I want them "before" I get stung and not after! 
Gone are the days of just grabbing the saw, heading out back, and cutting wood. It's safety first, then cutting.
Gone are the days of just grabbing the saw, heading out back, and cutting wood. It's safety first, then cutting.
simple.serf
Feeling the Heat
Between my dad and I we usually process 20 face cords a year. I am a fan of full PPE, just from my experience as a maintenance worker. I like having the glasses under the face shield (it's required where I work when grinding or cutting metal), and I have a pair that I carry in my truck that do not fog up. The other option is safety rated eye glasses with side shields, which work just as well.
I didn't used to be as aware of trying to use PPE, but then I ended up with a stainless sliver in my eye at work. Not fun.
I didn't used to be as aware of trying to use PPE, but then I ended up with a stainless sliver in my eye at work. Not fun.
My issue in the summer has been the glasses get steamed up with sweat, oily from chain oil wet gloves. It's a hazard not seeing well. I take the off. I know I shouldn't, but that's what happens.
What's the opinion on the face shield, screen type, verses a solid plastic lens?
What's the opinion on the face shield, screen type, verses a solid plastic lens?
I guess it makes sense even when cutting wood, you could hit a fence post buried n a tree and shrapnel could fly back into the mesh screen. Makes me rethink just the mesh thing, but I really do have a fogging issue.
I've always figured the mesh screen is really to protect you from branches flying back on your face, or maybe even snapped chain if it got that far. I still think you need safety glasses under neath. I have seen full plastic face shields but I would think they'd fog too. The best thing to do is keep safety glasses as far away from your face so air can move between the lenses and your skin. I have heard of "no fog" glasses but I haven't tried them. Anything is better than nothing for sure, but I try to wear actual safety glasses whenever possible. Chances are lower, but there's still a chance of a small particle making it through the mesh screen and into your eye. At that point, a little fogging suddenly becomes a very small nuisance....although it is a pain in the you know what!
The fogging is more than just a nuisance for me. It downright becomes dangerous seeing, like xman said. But I hear your point.
My screen is pretty small meshed, but there is always still a risk.
My screen is pretty small meshed, but there is always still a risk.
There are plenty of good non-fog safety glasses available. INHO there should be no reason to not wear glasses.
Remember, that wire screen is not always ANSI (safety) approved for flying objects (projectiles).
Usually the helmet portion is approved though. Of course SOME screen is, but make sure.
Also, a lot of moving sawdust and particles can find their way around (even through) screen.
My preference is BOTH mesh and "approved" glasses. YMMV.
I see guys all the time without eye protection on using chainsaws. I think its nuts.
D8Chumley
Minister of Fire
I always wear my Oakley m frame glasses. We have to wear full PPE at work-glasses, safety toe boots, 100% gloves hard hats and green vests with retro reflective strips. At first guys groan but I feel weird without it any more. I have 2 pr with dark and light polycarbonate lenses. I don't like the ones they provide as they put a weird effect on what I'm looking at whether running a dozer or excavator. I have chaps but don't use them much. I also have the hard hat with mesh screen and muffs that I don't use much either but I usually use ear plugs. Thanks to the OP for the reminder. Safety first!
Beer Belly
Minister of Fire
D8Chumley
Minister of Fire
I wish I could learn to remember to raise the face shield before I spit. 
D8Chumley
Minister of Fire
HAHA, now that's funny!I wish I could learn to remember to raise the face shield before I spit.
I must be a good squinter or just plain lucky. 30+ years of skillsaws, drills, grinders, chainsaws etc. Now I am at the age of needing "cheater" or reading glasses, I have a pair of tinted & clear safety glasses with the cheaters in them and find myself wearing one of them when ever I leave the house. Older and wiser? Slow learner? I still cut my wood in cut off jeans in the summer, and all my shoes are boots, so I guess, not old enough and still a slow learner
(broken image removed)
I just dug this out of Facebook. Here's my before and after picture that I posted on Facebook last year when my eye injury happened. The picture on the left is me at the Urgent care, moments after the doctor injected a "numbing medicine" in my eye...it completely took away my pain but they then told me it will last about 30 minutes, long enough for them to lift the flap I had cut in my cornea, cleanse the area, and re-seat everything. When they told me the extreme pain I felt moments earlier would come back soon, and remain for several days and there was nothing they could do for me to ease it until things healed...I was overtaken with dread. It's amazing how a tiny 3/8" slice in your eyeball can cause that kind of pain. It's indescribable.
The picture of me on the right is a week after the incident. I had just opened a package that arrived for me and was trying it all out in front of my girlfriend. As soon as I could see again (I was stuck at home with both eye's closed for 48 hours), I went online and ordered a safety helmet with face shield and Stihl's best safety glasses. As soon as I could drive I went to my Stihl dealer and bought a whole handful of safety glasses and placed them in the truck, on my table saw, on my weed wacker, chainsaw, riding mower, workbench, etc. Now, this is what I look like every time I touch a chainsaw... or any power tool, the lawn mower, etc. Please learn from my mistake so you don't have to suffer like I did. There's no reason to endure that kind of pain when someone who's been through it can tell you what can happen when you don't take safety seriously. I don't mean to harp on the subject or be a pain in the neck about it but...please wear your safety glasses. Be safe everyone!
I just dug this out of Facebook. Here's my before and after picture that I posted on Facebook last year when my eye injury happened. The picture on the left is me at the Urgent care, moments after the doctor injected a "numbing medicine" in my eye...it completely took away my pain but they then told me it will last about 30 minutes, long enough for them to lift the flap I had cut in my cornea, cleanse the area, and re-seat everything. When they told me the extreme pain I felt moments earlier would come back soon, and remain for several days and there was nothing they could do for me to ease it until things healed...I was overtaken with dread. It's amazing how a tiny 3/8" slice in your eyeball can cause that kind of pain. It's indescribable.
The picture of me on the right is a week after the incident. I had just opened a package that arrived for me and was trying it all out in front of my girlfriend. As soon as I could see again (I was stuck at home with both eye's closed for 48 hours), I went online and ordered a safety helmet with face shield and Stihl's best safety glasses. As soon as I could drive I went to my Stihl dealer and bought a whole handful of safety glasses and placed them in the truck, on my table saw, on my weed wacker, chainsaw, riding mower, workbench, etc. Now, this is what I look like every time I touch a chainsaw... or any power tool, the lawn mower, etc. Please learn from my mistake so you don't have to suffer like I did. There's no reason to endure that kind of pain when someone who's been through it can tell you what can happen when you don't take safety seriously. I don't mean to harp on the subject or be a pain in the neck about it but...please wear your safety glasses. Be safe everyone!
Sinngetreu
Feeling the Heat
I know this was kind of mentioned, but what about bug eyez for the fogging issue. You can get them in fine screen mesh. I know that the impact resistance is lower, but there is now way anything is getting to your eyes unless its through the screen.
http://www.wesspur.com/safety/tree-climber-eye-pro.html
http://www.wesspur.com/safety/tree-climber-eye-pro.html
Same here I wear a Stihl forestry helmet with metal mesh shield. Under that are safety glasses. I buy them by the half dozen from Harbor Freight, and they don't fog for me. What's ironic is that the more expensive models from other stores do fog.
http://www.harborfreight.com/garage-shop/eye-protection/impact-resistant-safety-glasses-94357.html
Firewood Bandit
Minister of Fire
I wish I could learn to remember to raise the face shield before I spit.
I can't tell you how many times I have done that.
- Status
