Durock for leveling insert?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
J

jophysx

Burning Hunk
Apr 12, 2011
191
SW Michigan
Is there any reason not to use a couple of layers of Durock or something similar on the bottom of the fireplace firebox to make a level surface with the exterior so the insert can be easily slid in and out? We have a raised hearth and the installer just used a couple of bricks to level the insert. It's awkward to get it in and out as is. Plus I like the idea of some extra insulation. Anybody have a better idea? The installation manual refers to leveling screws, but I don't know where those are. And the leveling screws would probably not be as simple as just a level surface to begin with.
-Jim

upload_2015-10-23_19-46-57.png
 
Should not be a problem as it is a common non-combustible hearth material but I am wondering what's the need for pulling the insert out regularly?
 
I've pulled it out to install a block off plate and then again to put in some insulation. I took those opportunities to clean the flue and decided that's an easy way to do it in the future.
 
Used Durock exactly as you showed. Worked perfectly and allowed the leveling legs to do what they are meant for, small adjustments.
 
and I like the idea of insulation between the insert and the floor. After seeing significant improvement in stove performance upon adding a block off and insulation, I am on the camp of "the more insulation the better". It keeps the heat in the firebox and into the house.
 
  • Like
Reactions: jatoxico
jatoxico said:
Used Durock exactly as you showed. Worked perfectly and allowed the leveling legs to do what they are meant for, small adjustments.
Click to expand...
Right on about the small adjustments. With my current setup I would have to extend the leveling legs about 2.5 inches. I'm not even sure they're that long. But even if they are, that much length puts a lot of torque on the mounts. I would be afraid of breaking them right off if I tried to move the insert once installed. So I'll go buy some Durock tomorrow and go ahead with the plan.
Thanks for the replies everybody.
 
I just did mine with hardie board, seems a little more durable. I figured the insert would less likely dig in while sliding it in.
I mixed up a real watery mortor mix and floated it level.
 
cableman said:
I just did mine with hardie board, seems a little more durable.
Click to expand...

I hope this does not start one of those "hardi-backer vs Durock" Threads. Nothing wrong with the hardi that I can tell. It's non combustible and as long as "R" value requirements are met, it should be fine. Yea Yea I know about the cellulose but it's still rated non combustible.

Can James Hardie products be used around a masonry fireplace?
Yes, HardieBacker® 1/4" Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4". Clearances to combustible building materials shall be obeyed even if they are protected by noncombustible materials, please refer to your local building and fire code for specific combustible clearance details around masonry fireplaces.
 
Status
Not open for further replies.

Similar threads

Mark218
New build - Stove in an alcove or wood insert?
Replies
23
Views
2K
The Hearth Room - Wood Stoves and Fireplaces
Mark218
Mark218
TomasB
Hearth extension is not supported nor attached?
Replies
107
Views
8K
The Hearth Room - Wood Stoves and Fireplaces
TomasB
TomasB
U
Converting an open hearth to stove in (combustible) alcove
Replies
17
Views
2K
The Hearth Room - Wood Stoves and Fireplaces
Dajolu
Dajolu
I
How to build an insert for a chimney liner
Replies
5
Views
1K
The Hearth Room - Wood Stoves and Fireplaces
webby3650
webby3650
T
Wood insert/Level-to-Level fan setup
Replies
7
Views
1K
The Hearth Room - Wood Stoves and Fireplaces
begreen
begreen
Top Bottom
Back