Timing issue...loading the stove when the stove isn't ready to be loaded

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
  • Super Cedar firestarters 30% discount Use code Hearth2024 Click here
Status
Not open for further replies.
Not a problem. Hope I didn't offend. Just wanted to point out the difference.
 
Thanks for the responses. I'm glad I didn't load up before bed. I left it as it. When I woke up, the stove was cold, and there was nothing but ash left. But the house was still warm, 68 degrees. Hopefully by winter, I'll get my timing down. :)

Ok, now I'm going to divert on my own thread a little. What if I did load up and had a run away situation? Is there anything that can be done to help bring the temps down? Fan on full blast? Damper open or closed? Open the door and throw in some wet paper towels? Thanks.
With the Castine, I can push a balled up wad of aluminum foi in the underneath air intake - have not had to do it yet, but I have learned where the intake is and I have the balled up foil that has been tested ready to go. I have heard of some that use a large magnet to cover the intake, but I would not know where to find one of those.
 
My first run away was a fright. I had the dog/cat carriers ready, while posting on here every 5 minutes.

BB & BG got me through it, thankfully. Pegged at 1000 on the thermo on the upper right hand corner of the face of the PE.

Coal bed at about 400, loaded it with rounds to stuff the box, as it was a wicked cold night. 10 minutes later, I'm at 650F , 15 minutes it's at 750 & climbing !!!

Never, ever load at 400F or more. Not worth it. Be cold in the morning. Save your sanity for other issues ;)

That being said, waiting for my coal bed on the PE to hit 350F, then reload for the night.

You'll get it, it's a game :)
 
  • Like
Reactions: gyrfalcon
We have had the same problem, you come home from work and want to load the stove, but if you do, it won't make it all the way to the AM if it's really cold out but it won't be burned down enough to reload before bed.

Here is how I handle this one: When you get home from work, throw in just a few splits of lower BTU wood like soft maple and open up the draft to burn it down fast. It throws lots of heat while you need it and burns nicely down to coals and is ready for the the full evening load.

This stuff about a runaway fire is a little foreign to me, with the Fireview and Progress I can have a 400F stove and even throw in bone dry Cottonwood with no problem - it damps right down. But with a non-cat stove there is more air even when it's fully damped down.
 
  • Like
Reactions: Batman
Same thing happens to catalytic stoves. I once threw an extra split on a big load with a very active cat. Got the scare of my life, cat temperature off the scale . not good. Don't do it.
 
  • Like
Reactions: begreen
Yes. When you get an major explosion of wood gas in a stove equipped and ready to burn it off, things will get exciting for a bit. The main thing here is to remain calm if it happens. And don't repeat that exercise.
 
I'm not suggesting everybody load a hot stove, but I can tell you I have done it numerous times with absolutely no problem, and I checked with Woodstock and they saw no problem. It seems these stoves simply have sufficient air control.
 
I'm not suggesting everybody load a hot stove, but I can tell you I have done it numerous times with absolutely no problem, and I checked with Woodstock and they saw no problem. It seems these stoves simply have sufficient air control.
Well, Tony, I have the Progress and have had it climb up to the upper 600s thanks to the cat eating too much smoke. The more you damp it down, the higher it goes. Sweating bullets, literally and figuratively... How do you control things in that situation?
 
Well, Tony, I have the Progress and have had it climb up to the upper 600s thanks to the cat eating too much smoke. The more you damp it down, the higher it goes. Sweating bullets, literally and figuratively... How do you control things in that situation?

Well, I'm not speaking for Tony for sure but I think you know my thoughts on this one. 600 degrees is a long ways from making me nervous. And yes, when you get the high temperatures, that stove top can get hot. You might remember the story about when I found my wife standing at the stove opening and closing the bypass because the stove top wanted to go over 700. I found she had closed the draft. So I simply went over and opened it to 1 (25% open) and the stove top did as expected; it cooled down and did not go over that 700 mark. So many times on these stoves it is good to give more air rather than less.
 
Hollow,

Believe it or not the way to control a cat stove that is climbing past 600 due to an engorged cat is to open up the draft! It seems counter intuitive, but it works, The idea is to speed the smoke travel so it does not have as much time contacting the cat. You can even try opening the bypass, but I usually just open up the draft about 1/4 to 1/3 for a while, and the temp drops.
 
Hey Tony, I didn't realize you were on line. Good advice.
 
Dennis, I learned from the best! ;)
 
When you get older, there won't be a "final reload" for overnight burns....you'll be getting up in the middle of the night for a "nature call", and throw in a piece or two like I do;lol

When you throw in a piece or two in the middle of the night, do you just leave the air closed down? I'm assuming you aren't going to stay awake and mess with air adjustments in the middle of the night. I'm still trying to learn some of the tricks. Thanks
 
When you throw in a piece or two in the middle of the night, do you just leave the air closed down? I'm assuming you aren't going to stay awake and mess with air adjustments in the middle of the night. I'm still trying to learn some of the tricks. Thanks

You shouldn't need to reload that Summit during the night, should easily burn through without needing wood. That's one of the stoves that I'd still like to test drive in my home.
 
I have never added wood after setting up the night load and going to bed in my life.
 
  • Like
Reactions: gyrfalcon
You shouldn't need to reload that Summit during the night, should easily burn through without needing wood. That's one of the stoves that I'd still like to test drive in my home.

You're right, I shouldn't ever have to. :) I was just wanting to know how he goes about it, and how it works out.
 
When you throw in a piece or two in the middle of the night, do you just leave the air closed down? I'm assuming you aren't going to stay awake and mess with air adjustments in the middle of the night. I'm still trying to learn some of the tricks. Thanks
I stay with it for about 15 minutes.....gotta walk the dog too....he's a senior also:rolleyes:
 
  • Like
Reactions: gyrfalcon
And that is what I did, and it worked! But it sure seemed like the wrong thing to do, but I did remember your wife's story Backwoods and clenched my teeth and turned it up.
Well, I'm not speaking for Tony for sure but I think you know my thoughts on this one. 600 degrees is a long ways from making me nervous. And yes, when you get the high temperatures, that stove top can get hot. You might remember the story about when I found my wife standing at the stove opening and closing the bypass because the stove top wanted to go over 700. I found she had closed the draft. So I simply went over and opened it to 1 (25% open) and the stove top did as expected; it cooled down and did not go over that 700 mark. So many times on these stoves it is good to give more air rather than less.

Now that you mention it, that is how I got the temp down. Thanks for the reminder ;em Trust me, you'll only have to mention it a couple hundred more times before it sticks...:confused:
 
  • Like
Reactions: Backwoods Savage
Wow, this was a good read. I have never known any of this. Just loaded the stove before bed and usually reload around 2-3 am when I get up to hit the head. Mine will be out in the morning if I don't reload. I don't hve a thermometer on mine anywhere. Where should I be measuring temps from ? I have a raytek laser thermometer.
 
What are ideal burn temps ?
I just shot mine. My stove is at about 420f and the flue pipe is about 250.
 
Ideal burn temperatures is whatever is required to heat the home. That can be regulated a lot just by the wood that you put in the stove. Not only the type of wood but the quantity. If little heat is needed, there certainly is no need to fill the stove. This morning was a good example. When we got up the sun was shining brightly and a warm, mid-30's day forecast. I put in 3 small splits of ash. That was good until around 5:00 when I added some. Now I wish I'd waited as it is hot in here.
 
Status
Not open for further replies.