pipe clearance to wall

[cheapheat5]

Hi, I am new to the site and to wood burning. I have built a corner hearth with proper clearances according to the manufacturer's specs. I have not added a mantle yet and i would like to use wood. I am reusing s/s 8 inch pipe with a 11.25'' galv. sleeve over it as a heat shield. I don't know if you can call this doublewall. Clearance to the mantle would be approx. 10'' from the outermost layer of pipe. Will this be enough?

 

[tfdchief]

Not sure I understand what you have. Can you post pictures? What kind of stove? Is the 8" SS the chimney connector for the stove? You might check this article on Hearth.com It may answer your question. https://www.hearth.com/econtent/index.php/articles/wood_stove_clearances_installing_it_safely

 

[cheapheat5]

I have a US Stove Co. Country Hearth model 2500. It does have a 6'' outlet. I was told I could use my 8'' s/s(take off from existing unused fireplace that came with house)without adverse affect on draft. Keep in mind I am new to this . I have read that double wall can reduce clearances down to 9'', however I was unsure that my setup was considered double wall and was unable to find the wording "stove pipe heat shield" that was referred to in the link- thank you for that. I have no pictures yet and my project is not complete- due to the fact that I am stuck with this. Thanks for your response.

 

[northernontario]

A true double-wall pipe (manufactured and stamped approved by a certified company) can be reduced to as low as 6" of clearance. A single-wall pipe, with a heat shield attached to it (or to the surface of the wall), with 1" of clearance for an airgap, reduces the clearance from 18" to 9". So, if you have a heat shield around for 8" pipe, with atleast a 1" gap between the pipe and shield, you can have 9" of clearance to combustibles.

Something to think about, if you're worried about clearances... a metal shield mounted 1" from combustibles (ie, mount it on the wall with a spacer) reduces stove clearances by 66%, and single-wall pipe by 50%. So if your mounting a heat shield, you might want to mount it to the wall instead of to the pipe... gives you more protection from the stove too.

https://www.hearth.com/econtent/index.php/articles/stove_wall_clear

 

[tfdchief]

I have a US Stove Co. Country Hearth model 2500. It does have a 6'' outlet. I was told I could use my 8'' s/s(take off from existing unused fireplace that came with house)without adverse affect on draft. Keep in mind I am new to this . I have read that double wall can reduce clearances down to 9'', however I was unsure that my setup was considered double wall and was unable to find the wording "stove pipe heat shield" that was referred to in the link- thank you for that. I have no pictures yet and my project is not complete- due to the fact that I am stuck with this. Thanks for your response.

I guess what I am worried about is we still don't know what the "8'' s/s(take off from existing unused fireplace"is exactly. Is this fireplace a prefab metal unit.? Does it have a Class A Chimney? Is that chimeny 8 in? All of what northernontario has said is good information. It all just needs to be applied correctly and I am still not comfortable with what you have exactly. Pictures would really help.

 

[cheapheat5]

The 8" stainless is pre-fab taken off of a martin industries fireplace. The galvanized heat shield was taken from the same unit. I have so far built a stone corner hearth and attached 1/2" durock to the walls spaced at 1" which I intend to tile. I ask the clearance question because I want to top the wall with a wood mantle. It would be ridiculous to go through all of this just to install a wooden mantle too close to the pipe. As it stands, I will have 10" of clearance between the heat shield and the mantle.