Regency i3100 insert cracks

[JMase]

Need some advice. My regency I 3100 was replaced in 2015 under warranty do to damage inside the firebox. Now in 2023 I have a few cracks and Regency denied my claim because you are only allowed one warranty claim replacement. Can this be welded or repaired? It’s right behind the holes on front of stove, regency said that’s part of the air wash system.

 

[begreen]

I'm not sure a weld will take there but it might be possible to bolt a plate that covers the crack.

Is there a liner on this insert? If so, how tall is it?

 

[JMase]

Liner in the chimney? Stainless liner yes, it’s a tall chimney 30 feet maybe

 

[begreen]

The stove is likely overfiring. The Regency is an easy breather and works well on a short chimney. On a tall one it needs a damper above the flue collar. There is a detailed thread on this problem and one solution. I'll see if I can find it.

A thermometer on the face of the insert above the door would help track stove temp.

 

[JMase]

 

[JMase]

Are you able to tell by photos where this crack is, hard to explain. Would you still burn with these cracks? I obviously do not want to buy another stove.

 

[begreen]

The cracks will get worse until further damage occurs. In the least, I would bolt a stainless plate across them to extend the life of the stove.

Here is the thread I referred to earlier.

Regency l3100 Cracks

Hello, this is a 7-year-old regency l3100. We are the original owners and had this installed in December of 2014. I cannot locate the receipt, and the ID tag is not visible in terms of the serial number. I've seen one or two other posts about this and wondering how people think this will play...

www.hearth.com

 

[JMase]

Also that area is bowed out so it’s not flat. Not sure if a plate over it will work. I’m not sure if sealing the cracks some how is an option. Is the stove unsafe to burn you think?

 

[JMase]

The cracks will get worse until further damage occurs. In the least, I would bolt a stainless plate across them to extend the life of the stove.

Here is the thread I referred to earlier.

Regency l3100 Cracks

Hello, this is a 7-year-old regency l3100. We are the original owners and had this installed in December of 2014. I cannot locate the receipt, and the ID tag is not visible in terms of the serial number. I've seen one or two other posts about this and wondering how people think this will play...

www.hearth.com

I saw that post, my cracks are not in that spot, they are inside on the top just inside the door

 

[begreen]

I saw that post, my cracks are not in that spot, they are inside on the top just inside the door

Correct, though I think the overfire condition is the same.

Also that area is bowed out so it’s not flat. Not sure if a plate over it will work. I’m not sure if sealing the cracks some how is an option. Is the stove unsafe to burn you think?

I was thinking a strip of stainless, maybe 22ga. not plate steel. You could try cleaning things up and apply JB-Weld's ultra high temp epoxy under the stainless patch.
It's not dangerous to burn in at this stage, but as those cracks open up it will start concentrating the heat more forward on the door area which could warp it. A good patch might buy 2-3 seasons if the stove is run at a lower temp.

 

[JMase]

Is this something a welder would do. I definitely can’t do it 😂

 

[JMase]

Here’s a video showing where it’s cracked

 

[JMase]

 

[bholler]

Yes that is a common place for cracking due to over firing I have fixed a few by cutting out the bowed section and bolting plate steel bent to fit over the area. But the over draft needs to be fixed or it will just happen again

 

[JMase]

Do I need a welder for this ? Who can repair it?

 

[farmwithjunk]

I can't really tell but is that piece removable? Looks like its part of the stove body from the pic/video. I don't see why a weld wouldn't hold?

 

[moresnow]

I’d put a straight edge across the upper sealing surface for the loading door gasket.
Looked like that area needs confirmation that it’s not distorted.
Maybe it’s just the video ?

 

[baysideburner]

I know this is an older post but dang u overtired that thing. Mines 11 years old and looks nothing like that. Every brick is destroyed all the metal is warped. Your burning too hot

 

[BigJ273]

I know this is an older post but dang u overtired that thing. Mines 11 years old and looks nothing like that. Every brick is destroyed all the metal is warped. Your burning too hot

That was my first thought also. That thing has taken a beating!

 

[bholler]

That was my first thought also. That thing has taken a beating!

It's a 30' tall liner. So it's constantly over drafting it needed a damper intake restricted etc

 

[baysideburner]

On the right side underneath the fan shroud is little hole. Put a magnet over it. It will block some incoming secondary air slow things down.

 

[bholler]

On the right side underneath the fan shroud is little hole. Put a magnet over it. It will block some incoming secondary air slow things down.

Yes but probably not enough at 30' that works good up to about 25'in my experience