Quadra fire my Vernon e2

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.

jordan69s

Member
Hearth Supporter
Jan 10, 2008
27
HUdson Valley NY
I replaced my Mt Vernon AE with this E2 about three seasons ago, after 15 years. In this heating season, it worked for about a week, and now I am getting four red blinking lights, and it seems like there could be many things wrong. The pellet stove will go through the testing run for about 20 minutes, and then the red lights come on. This has happened many times with my AE pellet stove, but normally pellets would be dropped, and then I would get whatever red light blinking indicating a problem. The vent is clean, the inside is cleaned and vacuumed, bottom tray is clean, too is properly sitting in place without any gaps, the only thing I have not yet done is to remove the outer fan and clean there. Is there a way to test the auger motor? My old AE auger motor worked u til the end; there was an issue with the motherboard, and I just did not want to put that much money into an old pellet stove, so a friend who used to sell pellet stoves sold me this one new, so three seasons seems crazy to have a bad auger motor… Any ideas or suggestions are greatly appreciated !
 
I
I replaced my Mt Vernon AE with this E2 about three seasons ago, after 15 years. In this heating season, it worked for about a week, and now I am getting four red blinking lights, and it seems like there could be many things wrong. The pellet stove will go through the testing run for about 20 minutes, and then the red lights come on. This has happened many times with my AE pellet stove, but normally pellets would be dropped, and then I would get whatever red light blinking indicating a problem. The vent is clean, the inside is cleaned and vacuumed, bottom tray is clean, too is properly sitting in place without any gaps, the only thing I have not yet done is to remove the outer fan and clean there. Is there a way to test the auger motor? My old AE auger motor worked u til the end; there was an issue with the motherboard, and I just did not want to put that much money into an old pellet stove, so a friend who used to sell pellet stoves sold me this one new, so three seasons seems crazy to have a bad auger motor… Any ideas or suggestions are greatly appreciated !
If you disconnect the auger motor you can use a "jumper" lampcord to run it. How is the flame during start up? Is the fire getting big/hot enough?
 

Attachments

  • [Hearth.com] Quadra fire my Vernon e2
    Test Cord.webp
    114.5 KB · Views: 4
I

If you disconnect the auger motor you can use a "jumper" lamp cord to run it. How is the flame during start up? Is the fire getting big/hot enough?
Thank you for your reply! The fire used to be strong and hot like in the last three seasons; the pellet stove is our only heat source. Just by looking I thought the auger motor was 12V. Good to know; I will test it with a lamp cord.
 
Thank you for your reply! The fire used to be strong and hot like in the last three seasons; the pellet stove is our only heat source. Just by looking I thought the auger motor was 12V. Good to know; I will test it with a lamp cord.
Unplug the stove for sure. If it does not turn right away, unplug it. Those little motors can stall and overheat.
 
I replaced my Mt Vernon AE with this E2 about three seasons ago, after 15 years. In this heating season, it worked for about a week, and now I am getting four red blinking lights, and it seems like there could be many things wrong. The pellet stove will go through the testing run for about 20 minutes, and then the red lights come on. This has happened many times with my AE pellet stove, but normally pellets would be dropped, and then I would get whatever red light blinking indicating a problem. The vent is clean, the inside is cleaned and vacuumed, bottom tray is clean, too is properly sitting in place without any gaps, the only thing I have not yet done is to remove the outer fan and clean there. Is there a way to test the auger motor? My old AE auger motor worked u til the end; there was an issue with the motherboard, and I just did not want to put that much money into an old pellet stove, so a friend who used to sell pellet stoves sold me this one new, so three seasons seems crazy to have a bad auger motor… Any ideas or suggestions are greatly appreciated !
So I removed the auger motor from the pellet stove and I provided power directly and it does turn. To my surprise, it turns very slowly, I guess in my mind, all shaft motors turn fast, and so I was holding it tight worrying that it was going to spin out of control. 😂. So the auger motor is working…
 
So I removed the auger motor from the pellet stove and I provided power directly and it does turn. To my surprise, it turns very slowly, I guess in my mind, all shaft motors turn fast, and so I was holding it tight worrying that it was going to spin out of control. 😂. So the auger motor is working…
The best way to test it now is feeding pellets. The problem could be within the auger / tube. They are usually 4 RPM, or 1 RPM. The motor itself is high speed, but there is a gearbox.