Rheostat (fan controller) issue

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.

Bill in the U.P.

Burning Hunk
Hearth Supporter
Dec 6, 2016
108
Michigan
Good morning. I have a 7 year old Blaze King King. We love it. The rheostat fan controller is on the fiitz. Pretty much the fan isn't working unless I slightly move the knob into the end range like I was turning it off. I taped it there with duct tape and it us running fine. Do I need to replace the switch? Where would I get the replacement? My dealer is an hour and half from me. I will check in with him in awhile (they are an hour earlier time zone).
 
Good morning. I have a 7 year old Blaze King King. We love it. The rheostat fan controller is on the fiitz. Pretty much the fan isn't working unless I slightly move the knob into the end range like I was turning it off. I taped it there with duct tape and it us running fine. Do I need to replace the switch? Where would I get the replacement? My dealer is an hour and half from me. I will check in with him in awhile (they are an hour earlier time zone).
You could just get a fan speed control from a hardware store if it's a115V motor.
 
Good morning. I have a 7 year old Blaze King King. We love it. The rheostat fan controller is on the fiitz. Pretty much the fan isn't working unless I slightly move the knob into the end range like I was turning it off. I taped it there with duct tape and it us running fine. Do I need to replace the switch? Where would I get the replacement? My dealer is an hour and half from me. I will check in with him in awhile (they are an hour earlier time zone).

Have you tried blowing out the fan housing with compressed air? Just a thought!
 
Have you tried blowing out the fan housing with compressed air? Just a thought!
OP could try bypassing the speed control and run direct. I assuming its a 115V motor. If it were somehow DC, you can't.
 
Thank you. Good suggestions. There are replacement rheostats (speed controller switches) avail online. I have found them priced from $15 to $57. I'll open things up and take a look today. I'll test the switch and blow things out and if its the switch I'll just direct wire the fans until the replacement arrives. (first snow accumulation as of today in pic).
 

Attachments

  • [Hearth.com] Rheostat (fan controller) issue
    1000014425.webp
    283 KB · Views: 20
  • Like
Reactions: Highbeam
Good morning. I have a 7 year old Blaze King King. We love it. The rheostat fan controller is on the fiitz. Pretty much the fan isn't working unless I slightly move the knob into the end range like I was turning it off. I taped it there with duct tape and it us running fine. Do I need to replace the switch? Where would I get the replacement? My dealer is an hour and half from me. I will check in with him in awhile (they are an hour earlier time zone).
I looked up the rheostat and motors. They are a 120V system for sure. The proper rheostat appears to have on/off, plus a lower voltage trim pot. With these motors you can't lower the speed too much. Full voltage (join the wires together) is fine. You will just have to unplug it.
PS - I like your setup. I live in the city and my view is another house or the street. I miss a real wood fire too.
 
[Hearth.com] Rheostat (fan controller) issue
[Hearth.com] Rheostat (fan controller) issue

Or, you could try the brilliant brainstorm that hit me after a mere 35 years of bending over and turning that pot switch on and off. Wire the fan through a thermistor controlled programmable Inkbird switch.
Now, the fan comes on only when there’s enough heat to justify it, and automatically switches off when temperature drops below a certain level.
Obviously some iterative tinkering with settings is required initially. The wire from sensor needs to be kept away from hot metal, and shouldn’t interfere with the throw of bypass door handle.
But now, for several years, I haven’t touched the pot switch, yet derive full benefit from fan, and never have to manually turn it off if/when stove cools down.
Best location for sensor IMHO is the air plenum itself.
 
Last edited:
  • Like
Reactions: Bill in the U.P.
View attachment 350613View attachment 350614
Or, you could try the brilliant brainstorm that hit me after a mere 35 years of bending over and turning that pot switch on and off. Wire the fan through a thermistor controlled programmable Inkbird switch.
Now, the fan comes on only when there’s enough heat to justify it, and automatically switches off when temperature drops below a certain level.
Obviously some iterative tinkering with settings is required initially. The wire from sensor needs to be kept away from hot metal, and shouldn’t interfere with the throw of bypass door handle.
But now, for several years, I haven’t touched the pot switch, yet derive full benefit from fan, and never have to manually turn it off if/when stove cools down.
Best location for sensor IMHO is the air plenum itself.
I love those Inkbirds. I have the WIFI ones on my brewing buckets. My latest use on one (like yours) was running a 20W 120V heater wrapped around a 2 inch pipe to preheat air. It feeds a traic controller so I can vary the heat output. You could also use snap switches for a stove if you could find a spot to mount one. You can buy a NO one that closes at whatever temp you want and wire in in series with the hot and speed control.
 
View attachment 350613View attachment 350614
Or, you could try the brilliant brainstorm that hit me after a mere 35 years of bending over and turning that pot switch on and off. Wire the fan through a thermistor controlled programmable Inkbird switch.
Now, the fan comes on only when there’s enough heat to justify it, and automatically switches off when temperature drops below a certain level.
Obviously some iterative tinkering with settings is required initially. The wire from sensor needs to be kept away from hot metal, and shouldn’t interfere with the throw of bypass door handle.
But now, for several years, I haven’t touched the pot switch, yet derive full benefit from fan, and never have to manually turn it off if/when stove cools down.
Best location for sensor IMHO is the air plenum itself.

The older BK stoves included this snap disc feature so that you never had to turn the fan on or off. Temperature made the connection. They abandoned that on newer BKs.
 
I love those Inkbirds. I have the WIFI ones on my brewing buckets. My latest use on one (like yours) was running a 20W 120V heater wrapped around a 2 inch pipe to preheat air. It feeds a traic controller so I can vary the heat output. You could also use snap switches for a stove if you could find a spot to mount one. You can buy a NO one that closes at whatever temp you want and wire in in series with the hot and speed control.

I added a huge fan to my noncat stove and used an adjustable snap disc to turn it on and off. Works great but looks pretty "industrial".
 
I added a huge fan to my noncat stove and used an adjustable snap disc to turn it on and off. Works great but looks pretty "industrial".
I was buying quite a few snap disk switches awhile back. I was experimenting with an outdoor heated birdbath. Once you are in the right place on Amazon there is quite a selection. You just need to be careful with NO verses NC and the temperature(and voltage/current too)
 
I was buying quite a few snap disk switches awhile back. I was experimenting with an outdoor heated birdbath. Once you are in the right place on Amazon there is quite a selection. You just need to be careful with NO verses NC and the temperature(and voltage/current too)

Exposed wires too. There are parts of this setup that you don't want to touch while powered up.