VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
This resonates a lot! I've always wondered if the griddle temp was inaccurate / not as good a gauge as the manual implies...

Thanks all for the input on the CAT -- I'll look into getting a new one ASAP. Is OEM best? Or do folks have preferred after market vendors?

Just as a sanity check, can someone confirm that for the Auber CAT probe I want the AT100TC/WRNK-191(6")?
I run then AT100TC (if you search I made a thread on installing it on my encore). I bought the longer thermocouple which is fine, but definitely longer than it needs to be.
 
  • Like
Reactions: Wannabe
It took me a while to tame my encore, i eventually partially blocked the secondary air; after replacing the door and griddle gasket, now the stove is much more tame / controllable. Now I can stuff it to the gills, and do most nights, without fear of it running away. I burned a lot of full loads of ash / maple last winter without overheating it. If you’re having issues still you may try that, my stove will burn anything now and has become quite reliable and consistent.

Once the OP gets a good CAT temp probe I’m sure we’ll be able figure out what’s going on. I’m suspicious most of his issues are related to how he’s operating the stove; and separately I’m suspicious that he has a very strong draft.
I re-did all my gaskets (minus dampener) and added 3' to the chimney this summer, back buffing was my biggest issue last season- so I'm optimistic about this season.
 
  • Like
Reactions: Turbo89
I re-did all my gaskets (minus dampener) and added 3' to the chimney this summer, back buffing was my biggest issue last season- so I'm optimistic about this season.
If you’re still having issues with high temps / not responding to reduced air, definitely try blocking part of the secondary. On the encore you can do it with a fridge magnet, I’m guessing all VC stoves are similar.
 
If you’re still having issues with high temps / not responding to reduced air, definitely try blocking part of the secondary. On the encore you can do it with a fridge magnet, I’m guessing all VC stoves are similar.
I have good air control but will look into doing that if I have issues - My main issue was lack of draft which caused back puffing, installing contractor installed 17' total vertical height with 2 90's, I have since added a total of 6' and guy support. Some leaks on the factory gasketing mainly ash pan and bottom of door - both confirmed by filling ash level to cover those areas and the stove works like it should.
 
I have good air control but will look into doing that if I have issues - My main issue was lack of draft which caused back puffing, installing contractor installed 17' total vertical height with 2 90's, I have since added a total of 6' and guy support. Some leaks on the factory gasketing mainly ash pan and bottom of door - both confirmed by filling ash level to cover those areas and the stove works like it should.
Yea, that makes a lot of sense; my VC has iabout 20’ straight up with no bends and drafts well. I replaced the ash tray gasket and checked door adjustment… it still burns better with a full tray; so I just leave it full / mostly full.

Cheers and happy burning.
 
Big update on my end--I'm tentatively calling victory on one big part of the problem--the stove running away / not respecting the air control without the damper enabled.

Someone mentioned it on this thread, but I actually was tipped off by this thread. It turns out that the secondary air intake was ajar in both the damper open and closed positions, when it should be closed when the damper is open. I'm almost certain this air was getting into the primary combustion chamber and causing the runaway / lack of control. I was able to take the heat shield off the back and adjust the chain attached to the damper by just two beads of slack and now it properly seats when the damper is open. I've done a couple test burns today/yesterday and I was able to keep the stove under 700 without the damper, which is a great sign (it would previously go to 800+ until I had to engage the damper, ember bed or none, just to quell the fire).

My guess is that the air control was more effective when the damper was closed because the smoke would go out past the secondary air intake, preventing it from entering the combustion chambers (and preventing draft stall?).

It's hard to see in this picture, but the bottom flap is the secondary air intake before the modification (the shadow hints at the lack of proper seating). I included a picture of the chain attached to the damper handle too, in case it helps anyone in the future.

My mind is kinda blown that this has been plaguing me for 3yr due to what looks like a factory / quality control issue... but really excited to see how it burns now.

I'll follow up again on the smoke opacity once I have a new CAT / the temperature probe installed! Thanks all for the help :)
 

Attachments

  • [Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
    secondary-chain.webp
    217.8 KB · Views: 20
  • [Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
    secondary-ajar.webp
    101.5 KB · Views: 20
That doesn't really sound like a top down. Here is a picture of the way I start that doesn't produce smoke.

Your cat is toast.. your using a metal cat which is great. I vacuum mine probably once a month or so when I clean out the ash. You should work on keeping the cat clean that is what is burning off the smoke. Also it's keeping your draft up when your burning low temperatures View attachment 350009
I lit the stove this morning so this is the picture above that hit me started

Picture 1 lighting with the torch
Picture 2 is 5 minutes after
Picture 3 is 10 minutes

After 10 minutes the stove was pretty much up to temp I'm just waiting for the stick to get warm enough for the cat to light off
[Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
[Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
[Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
 

Attachments

  • [Hearth.com] VC Intrepid Flexburn Woes / Help Diagnosing burn/smoke issues
    PXL_20261101_094149660.MP.webp
    201.4 KB · Views: 19
  • Like
Reactions: Wannabe